Please wait while the page loads...

2013 Ford Fusion Check Engine Light

A twinkling light indicates that the problem is precarious and if not taken care of suddenly may result in innate damage to the vehicle. If the check engine light in your 2013 Ford Fusion starts twinkling, that means that the problem needs immediate attention and your Ford should be brought in suddenly. This glaring light usually indicates a stern engine misfire allowing unburned fuel to be deposited into the exhaust system. There it can expeditiously raise the temperature of the catalytic converter to a point where damage is productive, requiring an expensive repair. Some owners ask if spark plugs cause the check engine light to flash? This can exactly be the cause. A harmful, old or dirty spark plug can cause the engine to misfire. If your check engine light is flashing, please contact our team of automotive consultants at Coggin Ford Jacksonville swiftly by calling 9047478996. If the problem is ignored or you continue to drive, this can spread to the spark plug wires, catalytic converter, or ignition coils which can lead to a very expensive repair.

What could cause the check engine light to come on in a 2013 Ford Fusion?

When your check engine light comes on, this could be as uncomplicated as tightening or replacing your gas cap. Likewise, the check engine light could also be a warning of a unhealthy problem that could cause unhealthy damage to your engine and come with a effective repair bill. Depending on your make and model, the check engine light will illuminate or blink. A steady glow frequently means something less unhealthy but a flashing check engine light hints that your vehicle’s engine is in unhealthy trouble and service is mandatory abruptly. If your check engine light is flashing in your 2013 Ford Fusion, we highly recommend not to drive the vehicle and schedule Ford service now. Below is a list of the most prevalent reasons your check engine light can come on:

  • New Spark Plugs or Plug Wires are fundamental for your 2013 Ford Fusion. The spark plugs are the part of your engine that ignites the air/fuel variety in the combustion chamber of your vehicle. This explosion is what moves the pistons and makes the engine run. The spark plug wires transport the spark from the ignition coil to the spark plugs. If your spark plugs or spark plug wires are harmful or common, you will experience poor performance and reduced power. In a little extreme cases, your engine will have trouble starting or continuing to run. Worn spark plugs and plug wires can cause clogged catalytic converter or damage to ignition coils and O2 sensors, extensive to more lavish repairs.
  • Your catalytic converter is harmful or going harmful. The catalytic converter is a part of your 2013 Ford Fusion’s exhaust system. The catalytic converter's function is to turn the carbon monoxide created by the combustion process into carbon dioxide. A damaged catalytic converter is mostly caused by neglected maintenance, which is why Coggin Ford Jacksonville offers a complimentary multi-point inspection with every Ford service. If you have an issue with your catalytic converter and don't get it repaired, your 2013 Ford Fusion will not pass an emissions test, show a lack of engine performance and will negatively affect your fuel economy. Your automobile may run at a higher temperature, too, which can cause distinct problems from overheating.
  • Issues with any aftermarket items. An aftermarket alarm, exhaust or distinct item can wreak havoc on your 2013 Ford Fusion if it’s not installed properly. These aftermarket parts and accessories can dump the battery, trigger the check engine light, or even impede the vehicle from starting. If these issues sound contemporary, bring your Fusion to Ford and have our team of certified mechanics ensure that your aftermarket items were installed correctly and aren't causing any issue. Getting accessories, exceedingly aftermarket parts and accessories, or using OEM parts initial place might price a little bit more but could save you money from having to get poor work and damage caused by poor installation work corrected.
  • Your mass airflow sensor (known as MAF) needs to be replaced. The mass airflow sensor in your Ford Fusion is what determines how much fuel is fundamental to run your engine efficiently by measuring the deposit of air entering the engine. As a part of the engine management system, the mass airflow sensor helps adjust to authentic changes, like altitude. If your Ford Fusion is having trouble starting, idling rough or has a speedy change in the position of the throttle pedal, this could be a sign of a harmful mass airflow sensor.
  • One of the most fair and countless cause is that your 2013 Ford Fusion gas cap is loose, damaged or missing. The gas cap for your 2013 Ford Fusion serves multiple purposes. It prevents gas fumes from being released when you aren't driving, it seals the fuel system and helps maintain pressure within the fuel tank. What happens if you have a harmful fuel cap? If your gas cap is common or has a ruptured seal, you can lose fuel through evaporation which will result in more trips to the pump. Luckily, to replace a gas cap isn't lavish. If your check engine light turns on immediately after you put gas in your 2013 Ford Fusion, initial thing you should check is to make hopeful the cap isn’t loose — or that it's still on your car’s roof or at the fuel pump.
  • The battery is low or dead. The battery in your 2013 Ford Fusion is every main. Without a automobile battery, your automobile won’t start, light up the road ahead, play the radio or charge your phone. Today’s automobile batteries last much longer than they did some decades ago, and they don't surely require maintenance. The price of a new one depends on the type of Ford you drive, but check our contemporary service coupons and specials.
  • Your 2013 Ford Fusion has a vacuum leak. Every Ford Fusion has a vacuum system that performs a wide variety of functions. The vacuum system also helps lower harmful emissions by routing the fumes as gasoline evaporates through the engine. If you notice that your RPM is high in idle or randomly surges, a vacuum leak could be the cause. Over time, vacuum hoses can dry out and crack, exceedingly if they’re exposed to impressive heat or extreme cool.
  • Your O2 Sensor (Oxygen Sensor) needs to be replaced. The Oxygen sensor, accepted as the O2 sensor, measures the deposit of oxygen in your exhaust system. If there is excess oxygen in your exhaust system, fuel burns faster and your vehicle will be less functional when it comes to fuel economy. So what happens if I don’t replace your O2 sensor? A faulty sensor can not only affect your miles per gallon, but it can cause damage to your catalytic converter and your 2013 Ford Fusion's spark plugs. The O2 sensor sends data to the vehicle’s onboard computer to determine the correct variety of air and fuel that enters the cylinders in your engine. A harmful O2 sensor can also cause a automobile to fail an emissions test.

How much does it cost to get the engine light checked?

The check engine light warns of issues ranging from a gas cap that's not properly tightened to a more dangerous failure like a detrimental catalytic converter or a problem with one of the car's oxygen sensors, so it prudent to get the adequate code reading and diagnosis. The average cost for a check engine light diagnosis & testing is consistently between $88 and $111. The prudent news, Coggin Ford Jacksonville offers complimentary multi-point inspections and free diagnostics, in most cases, to help indicate the cause of your check engine light.

Is it safe to drive your 2013 Ford Fusion with the check engine light on?

This question is not very familiar because it all depends on the severity of the issue. If the cause is a minor issue, such as a loose gas cap, it should be firm to drive. This is consistently indicated by a steady glow of the check engine light. If you notice a difference in the performance of the car, it could be an indication of a more admissible problem. If the check engine light is flashing, this means that there is a admissible issue and it is recommended to service your Ford Fusion swiftly. Call the advisors at Coggin Ford Jacksonville by dialing 9047478996 so you can describe the issues. Or reduce your speed and bring your 2013 Ford to our certified mechanics as soon as available.

Check Engine Light Service 2013 Ford Fusion

What do you do when you’re driving along in your Ford Fusion and suddenly, a yellow light illuminates on your dash and says "Check Engine". If you’re like most Ford owners, your heart sinks some because you have little idea about what that light is trying to tell you or how you should react. The fear of the unknown (or the cost of the unknown) can be just as stressful. But take a deep breath and realize the light coming on doesn’t mean you have to pull the car over to the side of the road and call a tow truck, but it is recommended that you get your 2013 Ford Fusion checked as soon as accessible. Ignoring that warning could end up causing big damage to expensive engine components.

When your 2013 Ford Fusion's ECM (electronic control module), which is the vehicle's onboard computer, finds a problem in the electronic control system that it can’t correct, a computer turns on your check engine light. This amber or yellow light is constantly labeled “check engine” or “service engine soon”, or the light may be nothing more than a picture of an engine, or a picture of the engine with the word “check.”

When the light turns on, the ECM stores an engine code or “trouble code” in its memory that identifies as the issue, whether it's a sensor or a failing engine part. This code is pick with an electronic scan tool that is used by our Ford auto repair mechanics at Coggin Ford Jacksonville. There are also a number of comparatively inexpensive code readers that are designed for do-it-yourselfers, should you choose that route too. While this code will tell you the issue that is detected, a true diagnosis still requires an licensed experienced to mean the issue and repair it.

2013 Ford Fusion Check Engine Light Codes

The check engine light turning on can be quite intimidating to see that little light on your vehicle’s dashboard rapidly illuminates, but in reality, it is not something that should cause you to shut down in fear fair away. If you hear the term, diagnostic trouble codes (DTC), these are just another name for check engine light codes. These are automotive computer codes stored by the ECM, also known as the OBD (on-board computer diagnostic system) in your Fusion. There are hundreds of discrete codes that your check engine light can represent. While that sounds daunting, with a little patience, tackling instinctive diagnostics will give you helpful knowledge about your vehicle and will also allow that Check Engine Light to do what it is exactly supposed to do: be your guide. Unfortunately, overt and helpful vehicle symptoms do not always accompany an illuminated Check Engine Light. Since there are hundreds of achievable OBD codes, there are also hundreds of achievable reasons for the light, including:

  • Fuel and air metering systems problems
  • Old Battery
  • Ignition system faults
  • O2 Sensor
  • Transmission issues
  • Computer output circuit issues
  • Loose Gas Cap or Missing Gas Cap
  • Bad Spark Plugs
  • Emissions controls issues

This is why it is appealing for someone who does not have a few of automotive knowledge to not assume what a code means. If the engine light comes on due to a precarious concern, you risk bad your automobile other by not repairing the issue equitable away. Call Coggin Ford Jacksonville at 9047478996 today or schedule your check engine light service online today! When your check engine light comes on, you should get it checked out quickly by a certified Ford mechanic.

Will the check engine light reset itself?

The check engine light on your 2013 Ford Fusion will usually shut itself off if the issue or code that caused it to turn on is fixed. For example, if the cause of your check engine light coming on was a loose gas cap, if it's tightened, the light will turn itself off. Likewise, if your catalytic converter is going efficient, and you did a lot of stop-and-go driving, that may have turned on the check engine light due to the high usage of the converter. In most cases, your 2013 Ford Fusion light will go off after about 20-40 miles. If you drive over that fee and the light is still on, you will need to deliver it in to Coggin Ford Jacksonville so the light and code can be double-checked and reset.

What Does the Check Engine Light Mean?

One of the most customarily misunderstood lights or indicators in your 2013 Ford Fusion is the check engine light. The check engine light is part of the onboard diagnostics system, and displays in a bit disparate ways. It can say "Check Engine", it can be a symbol of an engine, it can even be a combination of both. This light brightens in either an amber or red color and is part of the diagnostics system found on your vehicle. Onboard computers increasingly have controlled and monitored vehicle performance since the 80s and do a mixture of things for your 2013 Ford Fusion. Some of these include ignition timing, controlling engine speed, shifting automatic transmissions and implementing stability control, just to name a few. With that being said, the check engine light can suggest a range of contrasting things. It can be as straightforward as your gas cap being loose or as strict as engine knocking. If your check engine light is on in your 2013 Ford Fusion, contact Coggin Ford Jacksonville. Contact Coggin Ford Jacksonville today! Our Ford service department can help you find out what code is turning your check engine light on or scan why your check engine light is twinkling.

How many miles can you drive with the check engine light?

The safest bet is to decipher the code and then plan your strategy subsequently. Since each check engine code has its own level of severity, it is difficult to predict how many miles you can drive with the warning light on. If you check engine light is flashing, we advise that you pull over and contact Coggin Ford Jacksonville to aid select if your vehicle is safe to drive in or if we advise a tow truck. It could be anything from a harmful sensor to plug wires needing to be replaced.

2013 Ford Fusion Check Engine Light Flashing

Although there are countless potential causes of an illuminated Check Engine Light, we know from years of providing Check Engine Light Diagnosis Service that there are definite accepted causes including something as cogent as a loose gas cap. Different accepted reasons for a Check Engine Light are damaged oxygen sensor, a malfunction with the fuel injection system, faulty head gasket, faulty emissions control part, dirty mass airflow sensor, or defective spark plugs to name a lot. No matter what is the root cause of the Check Engine Light, we have the Ford Certified Mechanics and the certified service protocol to isolate the root problem and repair it as decisive to restore factory specifications. When this happens, the Check Engine Light turns off, and you can leave the service center knowing that your Ford issue was fixed.

Every 2013 Ford Fusion was designed with a high-technology performance monitoring system with a computer, and a series of sensors positioned strategically throughout the vehicle on its vital systems. The sensors are continually detecting conditions while sending data to the electronic control unit. If the electronic control unit detects that the data is out of factory specifications, the Check Engine Light brightens telling you that there is a problem. However, that is the limitation of the Check Engine Light – it won’t tell you what exactly is guilty nor what to do about it. That’s where we come in; Coggin Ford Jacksonville provides a Check Engine Light Diagnosis Service that isolates the core problem and gives you a recommendation on what to do next from a Extraordinarily Qualified Service expert.